s/v Bear at anchor, Scotland |
You can catch up with their sailing adventures on their website:
http://www.svbear.com/svbear_web_page/Welcome.html
Yvette, Mark, Jenefer and Maya |
and blog:
http://svbear.blogspot.com.au/
They have said their goodbyes to Russia and currently back in Sweden and enjoying the latter part of summer before heading back for winter storage.
On extended cruising such as this many problems arise in the maintenance of the boat and even though 'Bear' is a very strongly constructed and well found vessel, a lot of time is spent on keeping on top of the maintenance to ensure all parts are in 'best practice' condition for safe, happy and care free sailing.
Here is an extract from one of Mark's emails concerning the engine drive shaft coupler 'saver' he discovered about to blow:
'We have arrived at the Krestovski Yacht Club 59°57'59"N 30°14'48"E on Krestovski Island, St. Petersburg after the 200 mile from Tallinn, Estonia. We really did like Tallinn, it's a mix of the old Town from the new. We docked in the busy port 1000 yards from the cruise ships. The ships look so big from the water, we could not find the marina located just inland and behind the ships. There is good reasonable provisioning within a short walk of the Old Town marina. We had an excellent walking tour the day after we arrived. These poor people only gained there country from Russia between World War One and Two, then the Russians took them over again after the The Germans occupied during the war. We saw the old KGB headquarters, maritime museum. We found the Estonians to have a lot of resolve.
I
started doing my engine room check before leaving and found a large 5/8" bolt
in the bilge - not good! The engine coupler to the transmission was missing the
bolt. The other three were very loose. What a lucky find! I think after all the
lock dockings in the Gota Canal in Sweden they became loose. We pulled the
transmission in Florida before leaving and I did not re torque them. Luckily,
they were able to be tightened.
We
left Estonia around 10 a.m. it was flat calm as the forecast predicted. We found
a rocky shallow area to anchor around 11 p.m., off the coast of Finland but as
the anchor went down, the wind came up to 18 knots, and got really rough, we
pulled anchor at 1am and travelled the last 40 miles slowly as to arrive up the
narrow channel in daylight to the border control of Russia on Haapasari Island
Finland and arrived at about 0800. it is a small island off the Finnish coast
about 6 miles total land. We were Able to check in at Russian Passport Control
outpost and then stay at the dock until 4 p.m. for some sleep, but we paid the
price with big black tire marks on the hull left from the black tire fenders of
the dock. We left for the last 100 miles to St. Petersburg.'
Now Mark, apart from being a great family man, is also a first class sailor, marine surveyor by profession and with a big heart from which he willingly passes on any information, technical or otherwise that can be of assistance to the recipient sailor. He is also pretty creative when it comes to solving problems around the boat and here are a couple more things Mark has found work well on his ship, Bear:
He has installed raw water alarm to monitor raw water flow in the heat exchanger of his motor. This is a good peace of mind kit, especially if you are motoring over longer periods, say in a calm or you need some extra power to punch into rough weather.
These alarms will monitor your raw water flow and let you know if the flow is less than sufficient at which point your engine can begin overheating very rapidly. You can check out the Borel site http://www.borelmfg.com for further information and prices of these units.
Here's what Mark has to say and how he has it installed on his boat: 'The Borel engine exhaust temperature sensor. This inexpensive (under $100.00) US sensors strap onto the exhaust hose with simple plastic hose ties. You power with 12VDC and set the alarm in the cockpit or in our case next to the companionway. When the exhaust reaches 220 Degree, the alarm sounds. This is how the larger yacht engines are monitored. The exhaust gets hot when cooling water flow is not sufficient. The sensor picks this up and sounds the alarm. The engine water temperature gauges only alerts you once the engine is entirely hot, by which time internal damage could have already been done, or the cooling hoses have been overheated and become soft'.
No electric winches on your boat? Here is another very simple but huge labour saving device if you don't. The mast on Bear is sixty feet plus and that is a lot of winching past the point where the mainsail can be be lifted manually! Mark's solution is to use a Milwaukee vertical 1/2 battery power drill with winch bit to assist in raising the mainsail. As he points out it won’t lift the sail all the way, but does a pretty good job on the first 7/8ths of the raise. So winching the final 1/8th with fresh muscles is not so hard!
Mark has a few more innovations, problem solvers and fixes up his sleeve and these will appear in our subsequent posts.
We salute their ingenuity and wish the whole family to continue their happy and successful sailing adventure.
You can read much more about cruising the globe in my ebook 'Sailing Adventures in Paradise' by downloading it from my website http://www.sailboat2adventure.com/
Now Mark, apart from being a great family man, is also a first class sailor, marine surveyor by profession and with a big heart from which he willingly passes on any information, technical or otherwise that can be of assistance to the recipient sailor. He is also pretty creative when it comes to solving problems around the boat and here are a couple more things Mark has found work well on his ship, Bear:
He has installed raw water alarm to monitor raw water flow in the heat exchanger of his motor. This is a good peace of mind kit, especially if you are motoring over longer periods, say in a calm or you need some extra power to punch into rough weather.
Raw water alarm by Borel |
Here's what Mark has to say and how he has it installed on his boat: 'The Borel engine exhaust temperature sensor. This inexpensive (under $100.00) US sensors strap onto the exhaust hose with simple plastic hose ties. You power with 12VDC and set the alarm in the cockpit or in our case next to the companionway. When the exhaust reaches 220 Degree, the alarm sounds. This is how the larger yacht engines are monitored. The exhaust gets hot when cooling water flow is not sufficient. The sensor picks this up and sounds the alarm. The engine water temperature gauges only alerts you once the engine is entirely hot, by which time internal damage could have already been done, or the cooling hoses have been overheated and become soft'.
No electric winches on your boat? Here is another very simple but huge labour saving device if you don't. The mast on Bear is sixty feet plus and that is a lot of winching past the point where the mainsail can be be lifted manually! Mark's solution is to use a Milwaukee vertical 1/2 battery power drill with winch bit to assist in raising the mainsail. As he points out it won’t lift the sail all the way, but does a pretty good job on the first 7/8ths of the raise. So winching the final 1/8th with fresh muscles is not so hard!
Milwaukee drill set with winch bit |
We salute their ingenuity and wish the whole family to continue their happy and successful sailing adventure.
You can read much more about cruising the globe in my ebook 'Sailing Adventures in Paradise' by downloading it from my website http://www.sailboat2adventure.com/
2 comments:
Hi, Great post.Your sailing adventure looks awesome. Baltic and high altitude russian coast coast lies along waters that are frozen for many months of the year. But it is excellent for sailing.
Yacht charters
This is how the larger yacht engines are monitored. The exhaust gets hot when cooling water flow is not sufficient. Baltic Adventures
Post a Comment